Pen Making Supplies Logo
Have You Signed up for our Mailing List packed with free stuff, great offers and more??? 		Free Catalog
Penmaking Home Penmaking Index Page Penmaking Index Page Penmaking Index Page Pen Making Kits Pen Making Supplies Pen Making Supplies Penmaking Tools WoodWorkingCrafts.com Forums Steebar Home Page Pen Making Kits
Pen Making Supplies Micro Clock Necklace Kit PK-1088 Pen Making Supplies
Looking for Penmaking Instruction Sheets? | Search for:
KIT FEATURES
• Hanger stud
• Quartz Micro clock with a holding gasket (plus one spare gasket)
• Gold plated 27" long chain		 REQUIRED ACCESSORIES
• 15/16" Forstner bit
• Four prong drive center or a Woodworking chuck
• Drill bit – 9/64" diameter
• Required wood blank – 1-1/2" to 2" square x 2" long

PREPARING THE BLANK
Note: You may turn this project with either of the following two methods: A) a four-prong drive center and live center to support the wood on the lathe, or B) by holding the blank in a woodworking chuck.

Diagram A - Using a Drive Center Diagram

B - Using a Woodworking Chuck

PREPARING THE WOOD FOR DRIVE CENTER TURNING

  • Mark the center of the blank on the both faces. Drill a small pilot hole in one end of the blank; in the other end drill a 15/16" Forstner bit hole 1/4" deep.
  • Stud hole: mark the center thickness of your case design (see Diagram A). Drill a 9/64" hole in the center of the blank down to the large hole.
  • Use a mallet to force the drive center into the small pilot hole drilled into the wood.
  • Mount this assembly onto the headstock then slide the live tailstock center into the wood, lock it in place. (see Diagram A)
PREPARING THE WOOD FOR WOODWORKING CHUCK TURNING
  • Drill a stud hole – See instructions above
  • Mount the blank onto the chuck (See Diagram B)
  • Set the tool rest against the face of the blank, and find the center. Pencil mark a 15/16" diameter circle, Turn and cut a hole 1/4" deep in the surface, or use a 15/16" forstner bit. DO NOT OVER CUT!
  • Test the fit with the micro clock.

TURNING THE BLANK (Both Methods)

  • When the blank is locked, turn on the lathe. Cut away any excess wood and turn the case profile. Leave only enough wood to keep it from breaking apart.
  • Turn the case 1/2" to 5/8" thick and about 1-1/2" diameter.
  • Finish the wood, sand and polish.
  • Separate the case from the excess waste end with a parting tool.
  • Sand the excess projection out, round and smooth,
  • Touch-up the back face to restore the finish.
ASSEMBLY

Note: To achieve a high gloss finish use a high gloss project finish by brushing it on the case after final sanding and removal from the lathe.

  • Place a drop of glue inside the blank hole drilled for the stud.
  • Insert the threaded stud with the hole parallel to the case.
  • Set the time, if necessary, by pulling out the stem. Push the stem back in to start the clock.
  • Insert the chain through the hole in the stud.
  • To change the battery, use a sharp tool (i.e. knife); look for a projection on the back cover. The projection is about 1/4" wide, wedge the sharp tool into the gap and pull up gently. The cover will pop up. When covering the watch be sure to line up the rounded recession with the stem.

 

Search our site:
Search for:

Jump directly to a specific page

Want the inside scoop?

News and information, Steebar Exclusives,
Special Offers, Free Stuff and more!
Signup Here ..

On PenMakingSupplies.com you will find a complete line of Pen making kits, supplies and turning tools for the serious pencrafter. If there's something you can't find just send us an email and we'll be glad to point you in the right direction. Don't forget to stop by our wood working craft site WoodWorkingCrafts.com.

You may also be interested in our Clock Parts and Clock Making Supplies...


P.O. Box 607  Peapack, New Jersey 07977
Phone: (908) 204-0095 Fax: (908) 204-0099
Copyright © 2005, Steebar Corp.
Penmaking supply partner sites

 

 


pen making, pen supplies, pocket watch, pendant watch, pendant watch kits, liquid glass, epoxy resin, liquid glass epoxy